While there are many types of drawer slides one can purchase or make, I always seem to gravitate back to these full-extension ball bearing slides. I find I never have to worry about the drawer tipping out or binding the way I do with other systems. With that said, they are also extremely easy to install. If you haven’t already, check out our easy DIY Drawer tutorial (hint: no router or table saw required!), and then follow along below to get the drawer installed and sliding smoothly.

Note: Measurements and installation are tailored to our Midcentury Nightstand tutorial.

 

Cost: $12

Time: 20 minutes

Difficulty: Easy. With a couple careful measurements, these slides screw right into place.

Tape Measure

Pencil

Ruler or Straightedge

Drill/Driver

(1) Set of two Ball Bearing Full-Extension Drawer Slides sized to the inside depth of the cabinet.

Note: If you’re building a drawer using our tutorial, we’ll be using 14-inch slides.

-None-

 

Steps

 

1. Mark the Placement of the Slides

 

Measuring from the inside floor of the cabinet, mark a height of 8¼ inches near the front and back of each side wall. Using the marks and a straightedge, draw a level line across the wall on each inside wall of the cabinet. Make a mark on each line that’s 7/8 inch from the front edge of the cabinet. This allows room for the thickness of the drawer front plus an 1/8-inch inset.
How-to-Install-Drawer-Slides---Step-1-copy copy

www.Build-Basic.com2. Position the Slides

 

Align the bottom edge of the first slide above the line, as shown. Position the front edge of the slide behind the mark near the face of the cabinet.
How-to-Install-Drawer-Slides---Step-2-copy

www.Build-Basic.com

3. Install the Slides

 

Holding the slide firmly in place, push the extension forward until both sets of screw holes are visible. Using a drill/driver, drill shallow pilot holes in one screw hole near the front and back of the slide. Using the screws provided, mount the slide to the inside of the cabinet. Repeat steps 2 and 3 to mount the second drawer slide on the opposite side of the cabinet.
How-to-Install-Drawer-Slides---Step-3-copy

www.Build-Basic.com

4. Mark the Drawer Sides

 

Using a tape measure, mark the center of the height of the drawer box on its outer side walls. (Note: this drawer is shown without the drawer face, which will be installed at the end of this tutorial.) Using a straightedge, mark a horizontal line along the outside of the drawer box on each side.
How-to-Install-Drawer-Slides---Step-5

www.Build-Basic.com

5. Position the Slide Extension

 

Remove the detachable section of each drawer slides, and place it on the corresponding drawer side. Position the slides so that they are centered on their corresponding line and flush with the face of the drawer box, as shown.
How-to-Install-Drawer-Slides---Step-6-copy

www.Build-Basic.com

6. Attach the Slides to the Drawer

 

Using a drill/driver and the screws provided with the drawer slides, mount the slide to the drawer.
How-to-Install-Drawer-Slides---Step-7-copy

www.Build-Basic.com

7. Insert the Drawer

 

Hold the drawer level in front of the cabinet. Place the ends of the slides attached to the drawers into the tracks inside the cabinet. Pressing evenly on each side of the drawer, slide the drawer into place. The first slide inward can sometimes push a bit tougher, but once the tracks are engaged, the drawer should slide back out and in smoothly.
How-to-Install-Drawer-Slides---Step-8-copy

www.Build-Basic.com

8. Position the Drawer Face

 

Apply wood glue to the face of the drawer box. With the drawer closed, position the drawer face with equal gaps along the top and side edges. Using clamps, secure the drawer face against the drawer box.
How-to-Install-Drawer-Slides---Step-9-copy

www.Build-Basic.com

9. Attach the Drawer Face

 

Carefully slide the drawer open, and then drive 1-inch screws through the holes in the drawer box and into the backside of the drawer face to secure it in place.
How-to-Install-Drawer-Slides---Step-10-copy

www.Build-Basic.com

 

MORE BUILDING PLANS

 

 

27 thoughts on “How to Install Drawer Slides

  1. Connie Bolte

    Thank you for publishing these instructions. In my heart of hearts I always knew that the markup on these items is way up there. More than I can ever afford.

    Reply

Leave a Reply to Jenn Cancel reply