Create a stylish spot to display reminders and photos by layering fabric over inexpensive cork tiles. Back it with plywood, or install it inside a cabinet or storage chest (like we did). Lastly, finish the edge with a simple piece of trim to complete the look and hide the fabric’s rough edges. No matter the use, the simple construction and fabric overlay creates an instant upgrade from crafty to chic.

 

Cost: $20

Time: 1 hour

Difficulty: Easy. Just glue down the cork tiles and then finish with a layer of fabric and edge trim.

Tape Measure

Scissors

Circular Saw (or have the plywood cut at the homecenter)

Hammer and Finish Nails (or Pneumatic Nail Gun)

Handsaw (or miter saw)

Hand Stapler

X-acto Knife or Box-Cutter

(1) ½” x 2′ x 4′ Plywood Project Panel to make the backing (Note: the photos in this tutorial show the installation of the bulletin board on the inside of the flip-open lid to our DIY Filing Chest (Check back Tuesday for the reveal!), but ½-inch plywood can be used to make this a stand-alone wall item.)

(1) Pack of four 12-by-12-inch cork tiles

(1) Fabric. Get 1-2 yards depending on the configuration of your cork tiles.

(1) ½” x ¾” x 8′ Trim Board

5/8-inch Finish Nails to attach the Trim

¼-inch Staples

Wood Glue

Spray Adhesive

½” x 2′ x 4′ Plywood – 1 @ Length and Width of cork tile configuration plus a ¾-inch border on each side.

Fabric – 1 @ Length and Width of cork tile configuration plus a ½-inch overhang on each side

½” x ¾” Trim – 4 @ Custom cut to size

 

Steps

 

1. Size the Plywood

Layout the cork tiles on a work surface. Determine their configuration, (3-tile-high rectangle, large square, etc). Add the width of the ¾-inch trim to the length and width of the configuration. Mark and cut the plywood backing to size. (See our DIY Cutting Fence tutorial for detailed instruction.) For reference, our layout is 3-tiles-wide, and so the plywood would be 13½-inches-tall-by-38½-inches-wide. Because we’re installing the cork inside the lid of a flip-open storage chest, we’ll simply be centering the tiles on the ¾-inch-thick plywood lid.
Fabric-Bulletin-Board-by-Build-Basic---Step-1-copy

www.Build-Basic.com2. Size the Cork Tiles

 

If you’re installing the cork tiles inside a cabinet door or a flip-open lid like we are, you may need to trim them to a smaller size. If so, just mark the cut line with a marker or felt-tip pen, and then cut the line using a straightedge and an X-acto knife or box cutter. Be sure to place a cutting mat or scrap board under the cork before cutting, as shown.
Fabric-Bulletin-Board-by-Build-Basic---Step-2-copy

www.Build-Basic.com

3. Size the Fabric

 

Lay the fabric on the work surface, and then place the cork tiles in their configuration onto the fabric. Using scissors, cut the fabric about ½-inch from the edges of the cork. If the cork tiles are thicker than ¼ inch, leave enough fabric to drape over their edges, and comfortably onto the plywood for stapling.
Fabric-Bulletin-Board-by-Build-Basic---Step-3-copy

www.Build-Basic.com

4. Attach the Cork to the Plywood

 

Apply wood glue to the back of the cork tiles and to the plywood surface. Press the tiles into place, ensuring their outer edges align, and there are no gaps between the tiles.
Fabric-Bulletin-Board-by-Build-Basic---Step-4-copy

www.Build-Basic.com

5. Apply the Fabric

 

Spray the cork tiles with a light coating of spray adhesive to keep the fabric from shifting or pulling away from the cork. Lay the fabric in place, and then smooth out any wrinkles. Make adjustments until the overhang is equal on all sides, and the fabric is smooth.
Fabric-Bulletin-Board-by-Build-Basic---Step-5-copy

www.Build-Basic.com

6. Secure the Fabric

 

Press the nose of a hand stapler against the edge of a cork tile to tuck the fabric into the crease. Secure the fabric by shooting a ¼-inch staple through the fabric and into the plywood. Continue securing the fabric in place about every 2 inches along each edge.
Fabric-Bulletin-Board-by-Build-Basic---Step-6-copy

www.Build-Basic.com

7. Add the Trim

 

Using a miter saw or handsaw, cut the pieces of trim to size with opposing 45-degree miters at each end. (Note: I painted the trim before installation to avoid getting paint along the edges of the fabric.) Apply wood glue to the underside of the molding and the miter joints, and then press each piece into place against the edges of the fabric and cork. Clamp the molding in place, and then secure it using a hammer and finish nails or a pneumatic nail gun and 5/8-inch finish nails. Fill and sand the nail holes and miter joints, and then carefully touch-up the trim with paint.

Tip: Use our Safety Cutting Jig tutorial to get perfect miter cuts with a handsaw.

Fabric-Bulletin-Board-by-Build-Basic---Step-7-copy

www.Build-Basic.com

 

MORE BUILDING PLANS

 

One thought on “Build a Fabric Bulletin Board

Leave a Reply to lelobo Cancel reply