While the footprint of this cabinet is slim, it packs its punch on storage space. Use it as a Sideboard in a dining room, a dresser in the bedroom, or as a storage console near the entryway. No matter the use, you’ll be happy with the clean lines and versatile hideaway spaces. And while we rated this project at a higher difficulty level than most, it’s not necessarily because it requires a higher level of skill, but just that precision is key. But don’t worry, when it comes to positioning and installing the doors and drawers, we’ve got a trick up our sleeve that’ll make you come out looking like a pro!

 

TIP: Click the image above to reveal the free building plans. Click the tabs below to see the tools, materials and cut list.

 

Cost: $165

Time: 3 Work Days

Difficulty: Difficult. Keeping the cuts square and installing the drawer fronts and doors While the cuts are easy, installing the drawers and full-overlay doors requires patience and accuracy.

Note: This list may contain affiliate links

Miter Saw

Table Saw or Circular Saw

Kreg Jig

Drill/Driver

Pneumatic Nail Gun

Corner Clamps – Have at least two on hand, but four is better

24-inch Bar Clamps

Hand Clamps

Framing Square

Speed Square

Iron (to attach the edge banding)

Edge Banding Trimmer or small block plane

Pliers (if modify stock legs)

Hardware Installation Template to place knobs on Doors and Drawers

(2) ¾” x 4′ x 8′ Plywood

(1) ¼” x 4′ x 8′ Plywood

(8) Full Overlay Hinges

(2) Drawer Slides (sold in sets of two for each drawer)

(8) Door Pulls

(4) 3-inch Table Legs

(4) Footplates

(3) Rolls of Veneer Edge-banding

1¼-inch wood screws

1¼-inch Pocket Hole Screws

1¼-inch Finish Nails

1½-inch Finish Nails

 

Exterior

  • ¾” Plywood Top Board – 1 @ 51″ x 17½”
  • ¾” Plywood Bottom Board – 1 @ 49½” x 17½”
  • ¾” Plywood Side Boards – 2 @ 33″ x 17½”

Interior

  • ¾” Plywood Horizontal Divider – 1 @ 49½” x 16½”
  • ¾” Plywood Divider (Upper) – 1 @ 7″ x 16½”
  • ¾” Plywood Divider (Lower) – 2 @ 24¼” x 16½”

Drawers

  • ¾” Plywood Drawer Sides – 4 @ 6″ x 16″
  • ¾” Plywood Drawer Front and Back – 4 @ 6″ x 21 7/8″
  • ¼” Plywood Drawer Base – 2 @ 14½” x 21 7/8″

Back and Support

  • ¼” Plywood Back – 1 @ 32″ x 49½”
  • ¾” Plywood Vertical Supports – 2 @ ¾” x 27″
  • ¾” Plywood Vertical Supports – 2 @ 2½” x 27″
  • ¾” Plywood Horizontal Supports – 2 @ 2½” x 48″

Door and Drawer Fronts

  • ¾” Plywood Doors – 4 @ 8″ x 25 7/16″
  • ¾” Plywood Drawer Fronts – 2 @ 25 5/8″ x 12 21/32″

 

Steps

 

1. Cut the Parts

Using the cut list above, size the parts. If possible, aim to have vertical grain pattern on the Door and Sides, and horizontal grain pattern on the Top Board, and Drawer Fronts. If using a circular saw, be sure to check out my DIY Cutting Fence Tutorial to ensure the cuts are square.
DIY Sideboard Cabinet by Build Basic - Step 1

www.Build-Basic.com2. Prep the Parts

 

Using a Kreg Jig, drill three pocket holes into the underside of the Bottom Board and Horizontal Divider at each end. Drill additional pocket holes along the top edge of each Side Board, as well as all the Vertical Dividers.
DIY Sideboard Cabinet by Build Basic - Step 2

www.Build-Basic.com

3. Finish the Plywood Edges

Because we’re building with plywood, and not solid boards, it’s necessary to “finish” the exposed, rough edges. To do so, we’ll stick an adhesive strip of veneer onto the edges. See my full How To Finish Plywood Edges Tutorial for a quick primer. On this project, it’s necessary to finish the edges of the Doors and Drawer Fronts, as well as the ends of the Top Board. I also finished the front edge of the Bottom Board and each interior Divider, but it’s not necessary.
DIY Sideboard Cabinet by Build Basic - Step 3

www.Build-Basic.com

4. Mark a Centerline

 

Stack the Bottom Board, Horizontal Divider and Top Board on the work surface. Adjust the boards so that all their front edges set flush, as shown. Center the Bottom Board and Horizontal Divider on the length of the Top Board. Using a speed square, mark a centerline on the front edge of all three boards.
DIY Sideboard Cabinet by Build Basic - Step 4

www.Build-Basic.com

5. Carry the Centerline

 

Using a framing square, carry the centerline along both faces of the Bottom Board and Horizontal Divider, and along the underside of the Top Board.
DIY Sideboard Cabinet by Build Basic - Step 5

www.Build-Basic.com

6. Install the Vertical Divider (Upper)

Place the Top Board on the work surface with its underside facing upward. Apply wood glue to the top edge of the Vertical Divider (Upper). Center the board over the centerline marked on the Top Board. Use a framing square to ensure the Divider runs perfectly perpendicular to the frond edge of the Top Board. Clamp the Divider in place. Using a drill/driver and 1¼-inch pocket hole screws, attach the Divider to the underside of the Top Board.
DIY Sideboard Cabinet by Build Basic - Step 6

www.Build-Basic.com

7. Assemble the Top, Bottom and Sides

Stand the Top, Bottom and Side Boards on their back edge, and then place them loosely in the corner clamps. Position the Side Boards with their pocket holes facing inward. Rest the Top Board on top of the Side Boards, and the Bottom Board between them. Raise the Bottom Board ¼ inch from the bottom edge of each Side Board, as shown. The ¼-inch inset will help hide the footplate later on. Apply wood glue to the ends of the Bottom Board and to the top edge of the Sides. Clamp the boards in place. Check that joints are square using a framing square. You can also measure corner-to-corner, like an X, to help ensure the parts are clamped square. Using a drill/driver and 1¼-inch pocket hole screws, secure the pieces in place.

Build a DIY Sidaeboard Cabinet - Building Plans by @BuildBasic www.build-basic.com

DIY Sideboard Cabinet by Build Basic - Step 7

www.Build-Basic.com

8. Attach the Back Supports

Drill pocket holes at the ends of the 2½-inch-wide Back Support pieces. With the pocket holes facing the back of the assembly, position, glue and screw the pieces into place ¼-inch recessed from the back edge of the walls to allow room for the back panel later on. Finish by nailing the ¾-inch edge pieces using a pneumatic nail gun and 1¼-inch finish nails.

Build a DIY Sidaeboard Cabinet - Building Plans by @BuildBasic www.build-basic.com

DIY Sideboard Cabinet by Build Basic - Step 8

www.Build-Basic.com

9. Add the Horizontal Divider

Apply glue to the bottom edge of the Vertical Divider (Upper). Place the Horizontal Divider inside the assembled walls. Butt the Horizontal Divider up against the Vertical Divider (Upper). Drill 3 pilot holes through the underside of the Horizontal Divider and into the bottom edge of the Vertical Divider (Upper). Using 1¼-inch wood screws, secure the center of the Horizontal Divider in place.
DIY Sideboard Cabinet by Build Basic - Step 9

www.Build-Basic.com

10. Level the Horizontal Divider

Position and clamp the ends of the Horizontal Divider to the Side Boards equal distance from the Top Board. Using a drill/driver and 1¼-inch pocket hole screws, attach the ends of the Horizontal Divider to the Side Boards.
DIY Sideboard Cabinet by Build Basic - Step 10

www.Build-Basic.com

11. Insert the Lower Vertical Divider

Begin by sandwiching the two Vertical Dividers (Lower) together–with the pocket holes facing outward–using wood glue and several 1¼-inch finish nails. Center the joined Dividers inside the assembly using the marked centerlines. Using a drill/driver and 1¼-inch pocket hole screws, attach the top of each Divider to the underside of the Horizontal Divider. Finish by drilling pilot holes up through the underside of the Bottom Board and into the bottom edge of the Dividers. Secure the bottom edge of the Dividers using 1¼-inch wood screws.
DIY Sideboard Cabinet by Build Basic - Step 11

www.Build-Basic.com

12. Assemble the Drawers

Using the cut list above and my Easy DIY Drawer Tutorial, assemble both drawers. Set the assembled drawers aside for now.
DIY Sideboard Cabinet by Build Basic - Step 12

www.Build-Basic.com

13.Dryfit the Drawer Fronts and Doors

Lay the assembled cabinet on its back, and then rest the Drawer Fronts and Doors in place. To keeps the parts from shifting, clamp the Drawer Fronts flush with the surface and ends of the Top Board using bar clamps. Position and adjust the Doors below.

Jenn’s Tip: Use 1/8-inch tile spacers as placeholders for the necessary expansion gaps between the Doors and Drawer Fronts.

DIY Sideboard Cabinet by Build Basic - Step 13

www.Build-Basic.com

14. Prep and Stain the Parts

 

Before inserting the Drawers and attaching the Doors and Drawer Fronts, sand, stain, and polyurethane all the parts. If you’re modifying stock legs like I did, be sure to remove the adjustable footplate with a pair of pliers, and then tape off the metal base of each foot.
DIY Sideboard Cabinet by Build Basic - Step 14

www.Build-Basic.com

15. Attach the Drawer Slides to the Cabinet

Clamp a spacer block–I’m using 1×3 board with an actual width of 2½ inches–inside the drawer cavity, butted up against the underside of the Top Board. Remove the cabinet section of the drawer slide from each pairing. Hold the Drawer Slide firmly against the underside of the spacer block, and flush with the front edge of the cabinet. Using a drill, make shallow pilot holes at the front, middle and back of the drawer slide. Attach the drawer slide using the screws provided. Repeat to attach one slide to each side of both drawer cavities in the cabinet.
DIY Sideboard Cabinet by Build Basic - Step 15

www.Build-Basic.com

16. Attach the Drawer Slides to the Drawers

Clamp the spacer block to the side of the drawer, flush with its bottom edge. Place the rail on the spacer block. Position the rail flush with the front of the drawer. Using a drill, make shallow pilot holes at the front, middle and back of the rail. Attach the rail using the screws provided. Repeat to attach the remaining rails to each side of both drawers.
DIY Sideboard Cabinet by Build Basic - Step 16

www.Build-Basic.com

17. Insert the Drawers

Align the rails on either side of the drawer with the slides inside the cabinet. Lower the drawer evenly into place.
DIY Sideboard Cabinet by Build Basic - Step 17

www.Build-Basic.com

18. Attach the Drawer Faces

Apply wood glue to the front of each Drawer. Position the Drawer Fronts, and then lightly clamp them in place. Allow glue to dry completely before lifting the cabinet upright. Using a pneumatic nail gun and 1½-inch finish nails, nail through the Drawer and into the Drawer Front to hold the pieces securely in place.
DIY Sideboard Cabinet by Build Basic - Step 18

www.Build-Basic.com

19. Install the Doors

The small expansion gaps between the Doors and Drawers on the face of this cabinet leave little room for error. This means, the installation of the doors can get a bit tricky. With some trial and error, I found the easiest way to get the Doors into position is to first attach the hinges to the cabinet. I used a 1×5 spacer block to position my hinges, as shown. Next, close the hinges, position the Doors, and then clamp the Doors in place against the cabinet. Lastly, reach through the open back of the cabinet and screw the hinges to the backside of each door using the screws provided.
DIY Sideboard Cabinet by Build Basic - Step 19

www.Build-Basic.com

20. Add the Feet

 

Position the footplates ½-inch from the front and back edges and 2 inches from the ends of the Bottom Board. Drill shallow pilot holes through the plate and into the board. Secure the plates using the screws provided. Twist the threaded rod on each foot into a footplate. Now have a helper lift and set the cabinet on its feet.
DIY Sideboard Cabinet by Build Basic - Step 20

www.Build-Basic.com

21. Drill Holes for the Knobs

Using an Installation Template, drill pilot holes for each knob into the Doors and Drawers. On our Drawers, I centered the knob on the height of the 8-inch-tall Drawer Front, and brought each knob in 4 inches from the ends. On the Doors, I created my own hole in the template at 1¼-inches from each adjacent edge.
DIY Sideboard Cabinet by Build Basic - Step 21

www.Build-Basic.com

22. Insert the Knob

Insert the threaded rod on each knob into the holes. If the knob has a long thread like mine, it’ll work perfectly on the Drawers, but need to be trimmed on the Doors. Trim the rod after installation using bolt cutters or a hack saw, and then lightly file the cut end to get rid of any sharp points. If your knob has a short rod, you can always use a paddle bit to drill a countersink hole inside the drawer so that the nut can make it onto the threads.
DIY Sideboard Cabinet by Build Basic - Step 22

www.Build-Basic.com

23. Attach the Back

Apply wood glue to the backside of each Back Supports. Place the ¼-inch plywood Back Panel onto the Supports. The edges of the plywood should set inside the walls of the cabinet, and be hidden from view. Using a pneumatic nail gun and 1¼-inch inch finish nails, attach the Back by nailing though the plywood and into each of the Supports.
DIY Sideboard Cabinet by Build Basic - Step 23

www.Build-Basic.com

 

 

MORE BUILDING PLANS

 

3 thoughts on “Build a DIY Sideboard Cabinet

Leave a Reply to Free From Burdens Cancel reply