The word “drawer” followed by dados and dovetails is surly enough to scare off many a DIYer. Nonetheless, there’s an easier way to build a drawer without using a table saw or router, yet results in a beautiful, sturdy assembly just the same. Worried about visible fasteners? Our design cleverly hides them out of sight for a truly professional look. Follow along to see how you can quickly build any size drawer using this simple method. 

 

Want to download this plan? Click to view Build a Basic DIY Drawer on ETSY

 

Related Tutorials: How to Install Drawer Slides & Build a Midcentury Nightstand 

 

Cost: $6

Time: 1 ½ hours

Difficulty: Easy. Square cuts and pocket hole joinery make this a comfortable beginner project.

(1) 1 x 3 x 6 Board to make the drawer front, back and sides

(1) 1 x 6 Board to make the drawer front

(2) 3/8 x 3/8 x 3′ Square Dowel to make cleats

(1) ¼ inch Plywood to make the drawer base

(8) 1¼ inch Wood Screws to join the sides

(2) 1 inch Wood Screws to attach the drawer face

¾ inch Finish Nails to attach the cleats

Wood Glue

Wood Filler

Note: This cut list is sized to fit our Midcentury Nightstand

 

Find the downloadable plans HERE

 

Steps

 

1. Cut the Parts

 

Using a miter saw and the cut list above, cut the 1×6, 1×3, and square dowels to size. Mark cut lines on the face of the plywood using a framing square. Place painter’s tape over the cut lines, and then mark them again if necessary. The painter’s tape will keep the plywood from splintering during the cut. Cut along the lines using a circular saw. Lightly sand the cut edges of all the parts to remove burrs.

TIP: Check out our DIY Cutting Fence Tutorial for straighter cuts without a table saw.

Basic-DIY-Drawer-by-Build-Basic---Step-1-copy

www.Build-Basic.com2. Drill the Pocket Holes

 

Place the 1×3 front and back pieces on the work surface. Using a Kreg Jig, drill two pocket holes in each end of both boards.
Basic-DIY-Drawer-by-Build-Basic---Step-2-copy

www.Build-Basic.com

3. Drill the Drawer Face Holes

 

Place the 1×6 drawer face on the work surface with the pocket holes facing down. Using a tape measure and a pencil, make two marks 4 inches from the ends of the board, and centered on its width. Using a Drill/Driver, create two pilot holes. These pilot holes will later be used to attach the drawer face.
Basic-DIY-Drawer-by-Build-Basic---Step-3-copy

www.Build-Basic.com

4. Add Cleats to the Front and Back Pieces

 

Position an 18-inch cleat on the 1×3 front and back pieces flush with their bottom edges and ends. Apply a bead of wood glue to the cleat, reposition it, and then nail it in place using a pneumatic nail gun and ¾-inch finish nails.
Basic-DIY-Drawer-by-Build-Basic---Step-4-copy

www.Build-Basic.com

5. Attach Cleats to the 1×3 Side Pieces

 

Position the remaining cleats on the 16-inch-long sides flush with their bottom edges and centered on their lengths. This should create a 1 1/8-inch inset on each end of each cleat. Mark the ends of the cleats with a pencil. Remove the cleats, apply a bead of wood glue, and then put them back in place. Secure the cleats using a pneumatic nail gun and ¾-inch finish nails.
Basic-DIY-Drawer-by-Build-Basic---Step-5-copy

www.Build-Basic.com

6. Dryfit the Sides

 

Set the 1×3 pieces upright so that the cleats run along their bottom edge. Apply glue to the ends of the front and back pieces and then position them between the sides, flush with their ends.
Basic-DIY-Drawer-by-Build-Basic---Step-6-copy

www.Build-Basic.com

7. Assemble the Sides

 

In the name of not using fancy tools, I’ve used a very basic method for holding the joints square during assembly. Simply place a block (make sure it has a truly square corner) into the corner and clamp it tightly to each side. This will help hold the pieces in place while inserting and driving 1¼-inch pocket screws through the pocket holes and into the adjoining side. Once all four corners are assembled, check (and recheck) that the assembly is square by using a speed or framing square and measuring corner to corner.
Build a Basic DIY Drawer by Build Basic - Step 7 NEW

www.Build-Basic.com

8. Insert the Plywood Base

 

Apply a bead of wood glue to the top edge of each cleat. Position the plywood inside the frame on the cleats.

Tip: Once the drawer is painted or stained, I like to run a small bead of clear caulk along the edges of the plywood base to keep dust from falling between the plywood and the 1x3s. Additionally, if the drawer will hold heavy objects, consider using ½ inch plywood instead.

Basic-DIY-Drawer-by-Build-Basic---Step-8-copy

www.Build-Basic.com

9. Attach the Drawer Face

 

Center the front of the drawer on the 1×6 face. Depending on your application, allow the drawer face to hang below the drawer box. Mark the placement of the drawer on the 1×6, and then remove the drawer. Apply wood glue inside the marked area, and then reposition the drawer. Using a drill/driver, drive 1 inch wood screws through the pilot holes in the drawer front and into the backside of the 1×6 drawer face.

Tip: For a perfect fit, it’s best to fully install the drawer box, and then position and attach the face.

 

Tip: Check out our How to Install Drawer Slides tutorial.

Basic-DIY-Drawer-by-Build-Basic---Step-9-copy

www.Build-Basic.com

 

MORE BUILDING PLANS

 

50 thoughts on “Build a Basic DIY Drawer

  1. Kevin

    I’d like to know how the price of this project is $6. Where are the materials being sourced from? Any pricing I do online comes out to way more than $6.

    Reply

  2. Michael P

    HI Jen:
    Can you tell me why and what is the purpose for a kitchen drawer with the drawer bottom requiring grooves/slits to slide the bottom panel into the sides or installing cleats to rest the bottom panel on? In other words, why not just attach (either with secure pocket holed screws or with a nail gun) the bottom panel directly flush to the bottom area of all the drawer sides leaving NO 1/4 inch gap (slit, grove or cleats)? If my kitchen base cabinets are Euro Style (with no face frame) and I just use the ball bearing side mount gliders (and NO under mount gliders) for MDF drawers would that bottom panel require that 1/8 or 1/4 space under the drawer bottom panel? I’m new to woodworking and I can’t seem to find the answer for the purpose of that gap on the bottom and why a flush mounted bottom panel attached to all drawer sides is considered a “no-no” in cabinetry making, please explain…I’m puzzled?

    Reply

    1. Rick J.

      I am not a carpenter…..But I did not see any replies to your question. I think the reason drawer bottoms are always put inside a slot or on cleats is to keep the bottom ever falling off to the floor or next drawer. With use over time this could happen much easier if you just nail the bottom the flush. This is just in my opinion. I could be wrong.

      Reply

    2. Joe

      I’m new to wood working also but not yo carpentry or construction. I’d say the gap is to allow for the weight of whatever will be in the drawer for when it “sags”. Or when you pull the drawer out and place it on the floor or table you won’t scuff the bottom. Regardless of stick with it NOT being flush with the bottom.. insolent “cap off” the bottom either. Both would just look and be tacky/unprofessional

      Reply

Leave a Reply to Anonymous Cancel reply