Pretty much every piece of furniture at Ballard Designs makes me swoon, but the industrial Allen Side Table is especially jaw dropping. Unfortunately, the $199 price tag makes me weak in the knees…in a bad way. Luckily a quick trip to the home center for a pre-cut wood round and some black pipes make this an easy and inexpensive DIY project! The only thing that took some time was getting the shape of the legs just right. Luckily, I made a handy printable template so you can just trace it onto a board, and then cut them out with a jigsaw! As for the base, I made my own out of a scrap piece of a 4 x 4 post, but you can always sub in the octagonal top section of a store-bought table leg to make it easier.

 

P.S. Did you see my selfie video sneak peek of this project on Facebook? Click HERE to check it out!

 

TIP: Click the image above to reveal the free building plans. Click the tabs below to see the tools, materials and cut list.

 

Cost: $30
Time: 4 Hours
Difficulty: Easy. Tracing the template and cutting out the legs is easy. If cutting the Base feels outside your comfort zone, just substitute the top section of a store-bought table leg!
Note: This list may contain affiliate links

(1) 1 x 6 x 6′ Board to make the Legs
(1) 18-inch Wood Round to make the Top
(1) ½” x 1½” Hobby Board to create the Feet
(1) 4 x 4 Kiln Dried Post to create the 4½-inch-tall Base
*Tip – You can also substitute the Base for the octagonal upper part of a store-bought table leg
(1) 1″ x 8″ Black Steel Pipe Nipple

(1) ¾” x 4½” Black Steel Pipe Nipple

(1) 1″ x 2″ Black Steel Pipe Nipple

(1) 1″ Black Steel Threaded Floor Flange

(4) ¾-inch Wood Screws to attach the Flange to the Wood Round Top

(8) 1¼-inch Coarse Thread Pocket Hole Screws to attach the Legs to the Base

(4) 1¼-inch Finish Nails to Attach the Feet to the Legs

(1) Decorative Knob

Glue rated for use on both Metal and Wood

Wood Filler

4 x 4 Base – 1 @ 4½ inches (bevel the corners to create an octagonal base)

1 x 6 Legs – 4 @ Cut to Size using my FREE TEMPLATE

½” x 1½” Feet – 4 @ 2½ inches

Steps

 

1. Trace the Leg Template

 

Download and print my FREE TEMPLATE. Cut out the template, and then place it on a 1 x 6 board. Trace the shape of the Leg onto the board. Move the template along the board, and then trace the outline again. Repeat this process until all four Legs are outlined on the board.
Ballard-Inspired Side Table by Build Basic - Step 1

Blog-Step-by-Step-Line-200

2. Shape the Legs

 

Clamp the board to a sturdy work surface, and then cut the outlined Legs using a jigsaw. Move and re-clamp the board as needed to finish cutting the remaining Legs.
Ballard-Inspired Side Table by Build Basic - Step 2

Blog-Step-by-Step-Line-200

3. Prep the Legs

 

Using a random orbital sander, sand the edges of each Leg smooth. Place the Legs on top of one another, to ensure their lengths are even, which will create a level table. Lastly, using a pocket hole jig, drill two pocket holes along the 3½-inch flat edge of each Leg, as shown.
Ballard-Inspired Side Table by Build Basic - Step 3

Blog-Step-by-Step-Line-200

4. Add the Feet

 

Add ½-inch-thick blocks to the bottom of each Leg. To do so, apply wood glue to the bottom of each Leg, and then center it on a block. Allow the glue to set for a minute or two. Now, flip the Leg over and drive a 1¼-inch finish nail through the Foot and into the Leg to secure it in place.
Ballard-Inspired Side Table by Build Basic - Step 4

Blog-Step-by-Step-Line-200

5. Mark the Post

 

Using a straightedge, mark a line 1-inch from each edge of the post on all four faces.
Ballard-Inspired Side Table by Build Basic - Step 5

Blog-Step-by-Step-Line-200

6. Cut the Post

 

Using a circular saw set to a 45-degree bevel, cut along the lines to shape the Base. Only cut about 5 inches along each line on the post. Tip: If this cut seems outside your comfort zone, use the octagonal top section of a store-bought table leg instead.
Ballard-Inspired Side Table by Build Basic - Step 6

Blog-Step-by-Step-Line-200

7. Size the Base

 

Wrap a piece of painter’s tape around the entire cut end of the post. Mark a length of 4½-inches on the post, and then cut the post to size. Remove the painter’s tape and beveled pieces to reveal the octagonal Base.
Ballard-Inspired Side Table by Build Basic - Step 7

Blog-Step-by-Step-Line-200

8. Mark the Base

 

On the top and bottom of the Base, mark diagonal lines between the corners that intersect to locate the center of the block.
Ballard-Inspired Side Table by Build Basic - Step 8

Blog-Step-by-Step-Line-200

9. Drill Holes for the Pipes

 

Secure the Base between two blocks clamped to the work surface to prevent it from spinning. Using a drill/driver fitted with a forstner bit, drill a 1½-inch-deep hole into the top of the Base, and a 1-inch-deep hole into the bottom of the Base. While drilling, be careful to keep the drill bit plumb (perfectly vertical) so that the pipe will set properly into the hole.
Ballard-Inspired Side Table by Build Basic - Step 9

Blog-Step-by-Step-Line-200

10. Attach a Leg to the Base

 

Apply wood glue to the flat edge of a Leg, and then clamp it onto a face of the Base. I’m using the original faces of the post–not the area where I beveled the corners off–because I know they are square to each other. Position the Leg ½-inch from the top edge, and centered of the Face. Drive 1¼-inch pocket hole screws through the Legs and into the Base to hold the pieces in place.
Ballard-Inspired Side Table by Build Basic - Step 10

Blog-Step-by-Step-Line-200

11. Attach the Remaining Legs

 

Apply wood glue to the remaining Legs, and then position and screw them into place. Fill the pocket holes with plugs or wood filler. Allow the wood filler to fully dry, and then sand the Legs smooth.
Ballard-Inspired Side Table by Build Basic - Step 11

Blog-Step-by-Step-Line-200

12. Prep the Pipe

 

Just for looks, I had the Home Center cut the threads off one end of the 1-inch pipe. About ½ inch from the cut end of the pipe, I’m installing a knob to match the original project, even though my table height won’t be adjustable. To do so, secure the pipe between two blocks clamped to the work surface, and then drill a hole sized to the base of the knob.
Ballard-Inspired Side Table by Build Basic - Step 12

Blog-Step-by-Step-Line-200

13. Join the Pipes

 

To create a decorative change in the thickness of the pipe, and make it “look” adjustable, apply glue to one end of a ¾-inch pipe, and then twist it into the 1-inch pipe until the threads no longer show.
Ballard-Inspired Side Table by Build Basic - Step 13

Blog-Step-by-Step-Line-200

14. Install the Knob

 

Apply glue to the base of the decorative knob, and then press it into the hole drilled in Step 12. Allow the glue on the joined pieces to dry.
Ballard-Inspired Side Table by Build Basic - Step 14

Blog-Step-by-Step-Line-200

15. Install the Pipe

 

Apply glue to the base of the 1-inch pipe. I’m using glue that expands as it dries to ensure the pipe has a tight fit inside the Base. Place the pipe into the hole in the top of the Base.
Ballard-Inspired Side Table by Build Basic - Step 15

Blog-Step-by-Step-Line-200

16. Position the Pipe

 

Place a small level on the installed pipe, and then position it so that it sets plumb (perfectly vertical). Apply painter’s tape to the pipe and base to hold the pipe in place. Allow the glue to dry according to the manufacturer instructions. I allowed my glue to dry for several hours, but it was still wobbly. Luckily, after letting it set overnight, it was a fully bonded, strong connection.
Ballard-Inspired Side Table by Build Basic - Step 16

Blog-Step-by-Step-Line-200

17. Add the Tail

 

To make it look like the pipe extends through the Base, glue the short 2-inch threaded pipe into the hole in the bottom of the Base. Allow the glue to dry.
Ballard-Inspired Side Table by Build Basic - Step 17

Blog-Step-by-Step-Line-200

18. Install the Top

 

Using a drill/driver, attach the floor flange to the underside of the wood round using four wood screws. Twist the Top onto the Base to complete the assembly.
Ballard-Inspired Side Table by Build Basic - Step 18

Blog-Step-by-Step-Line-200

 

MORE BUILDING PLANS

 

10 thoughts on “Ballard-Inspired Side Table

  1. Pingback: Industrial Round Side Table - KnockOffDecor.com

Leave a Reply to Anonymous Cancel reply